Exploration and Production Core Competency eLearning Library

Enterprise-wide eLearning for Operations and Maintenance Personnel

ePilot™ Learning Libraries allow you to incorporate effective elearning into your development programs with hundreds of courses and thousands of hours of industry-validated content. Proven instructional design methodology and advanced web technology provide effective knowledge transfer for learners.

Exploration and Production Core Competency

  • Gas Measurement: Electronic Flow Measurement
  • Gas Measurement: Equipment and Calculations
  • Gas Measurement: Fundamentals
  • Gas Measurement: Orifice Flow Calculations
  • Gas Measurement: Orifice Meters
  • Gas Measurement: Witnessing
  • Glycol Dehydration
  • Heater Treaters: Fundamentals
  • Heater Treaters: Types and Operation
  • Hydraulic Subsurface Pumping Systems: Downhole Pumps and Engines
  • Hydraulic Subsurface Pumping Systems: Installation and Testing
  • Hydraulic Subsurface Pumping Systems: Pump Performance
  • Hydraulic Subsurface Pumping Systems: Surface and Tubing Equipment
  • Introduction to Service Rig Operations
  • Lease Automatic Custody Transfer (LACT)
  • Lease Instrumentation: Control Equipment
  • Lease Instrumentation: Final Control Devices
  • Lease Instrumentation: Sensing and Measuring Equipment
  • Oil and Gas Production Overview
  • Oil and Gas Reservoirs: Barriers and Traps
  • Oil and Gas Reservoirs: Fundamentals
  • Oil and Gas Separators
  • Oil Field Corrosion
  • Oil Field Electricity: Conservation and Classification
  • Oil Field Electricity: Electrified Equipment
  • Oil Field Electricity: Fundamentals
  • Oil Field Electricity: Offshore Oil Field Electricity
  • Oil Well Performance and Surveillance: Equipment
  • Oil Well Performance and Surveillance: Fundamentals
  • Oil Well Performance and Surveillance: Testing
  • Plate Tectonics
  • Process Component Safety Analysis and System Testing
  • Production Facility Gas Processing
  • Production Safety Equipment and Support Systems
  • Production Safety Systems Regulations and Device Identification
  • Reducing Marine Trash and Debris
  • Safety Device Operation
  • SEMS Standard and Requirements
  • Testing and Setting Safety Devices
  • Vapor Recovery Systems
  • Water Treatment and Disposal: Facilities and Testing
  • Water Treatment and Disposal: Fundamentals
  • Water Treatment and Disposal: Processes and Equipment
  • Well Control and Production Safety Regulations
  • Well Pumping: Introduction to Sucker-Rod Systems
  • Well Pumping: Operating Sucker-Rods
  • Well Pumping: Sucker-Rod Pump Performance
  • Well Pumping: Sucker-Rod Surface Equipment
  • Well Pumping: Sucker-Rod Systems
  • Wireline and Sonar Well Operations


Duration: 4 Hours

This program first reviews the reasons for artificial lift. Then, it explains the principles of a centrifugal pump and how such a pump can lift well fluids. The program shows the location of pumping system equipment, both at the surface and downhole. Then the program details the specifics of the downhole equipment and its operation. Once downhole operations are covered, the function of the motor control panel and other surface equipment is described. And finally, the careful handling of electrical cable is discussed.




Duration: 2 Hours

In this program, you will learn that routine ammeter chart reading and prompt reporting of pumping system problems are ways to minimize maintenance costs. You will also learn how to read ammeter charts and how to avoid some common operating problems.


Duration: 3 Hours

Flowing Wells is a series of six structured learning programs designed for the lease operator at a flowing well. In Chokes, the fifth program in the series, you will learn about the kinds of chokes used at a wellhead to control flowing wells, how they are installed, and how they are adjusted. You will also learn how to select the choke size needed for any particular well.



Duration: 4 Hours

Flowing Wells is a series of six structured learning programs designed for lease operators at a flowing well. In this first program, Introduction to Pressure and Flow, you will learn about the basic properties of fluids and the nature and causes of fluid pressure. You will also learn the factors that affect the flow rate of fluids and the basic principles of flow control.



Duration: 3 Hours

Flowing Wells is a series of six structured learning programs designed for the lease operator at a flowing well. In this final program in the Flowing Wells series, you will learn how to open the well, how to shut it in, how to stop-cock a heading well, and how to equalize a well to return it to flow. You will also learn to identify and solve problems likely to occur in flowing wells.



Duration: 3 Hours

Flowing Wells is a series of six structured learning programs designed for the lease operator at a flowing well. In Packers and Valves, the fourth program in the series, you will learn about the types, function, and installation of packers in a producing well. You will also learn about the installation, function, and construction of surface valves and auxiliary equipment.




Duration: 3 Hours

Flowing Wells is a series of six structured learning programs designed for the lease operator at a flowing well. In this third program in the series, you will learn about the structure of a producing well and the location and function of wellhead and wellbore equipment. Finally, you will learn about the components of the Christmas Tree.



Duration: 4 Hours

Flowing Wells is a series of six structured learning programs designed for the lease operator at a flowing well. In this second program in the series, you will learn to analyze wellbore pressures and predict their changes. You will learn to recognize the flow patterns that develop in producing wells, and how pressure drops affect flowing fluids. Finally, you will learn about the conditions that lead to solid deposits in the wellbore and surface lines.


Duration: 4 Hours

In this program, you will learn about the types of fluids and their chemical and physical nature, the nature of phase, how phase change is used, and how it can be controlled. The program goes on to cover the instruments and units for measuring fluids. This includes units for measuring pressure, temperature, density, and viscosity. You will also learn about the nature of absolute measurements and how to convert measurements from one unit to another.



Duration: 3 Hours

In this program, you will learn how to predict pressure, temperature, and volume changes that occur in gas compression and storage. You will also learn to recognize hazards in gas handling and the precautions used to avoid these hazards. This program also covers the nature, calculation, and uses of static pressure, including how to calculate pressure from liquid level and liquid level from bottom gauge pressure, the instruments that operate on the principle of static pressure, the nature and hazards of vacuum; and the uses of static pressure in handling and transporting fluids.


Duration: 3 Hours

The injection of gas into the well fluids in the tubing of an oil well is one method of artificial lift. Gas Lift is a series of three learning programs describing this method in detail. In Gas Lift: Equipment, you will learn specifics about the equipment used in gas lift operations, including monitoring and measuring equipment, gas lift valves, mandrels, fluid pressure operated valves, reverse check valves, and bottomhole installations.



Duration: 2 Hours

The injection of gas into the well fluids in the tubing of an oil well is one method of artificial lift. Gas Lift is a series of three learning programs describing this method in detail. Fundamentals introduces the characteristics of reservoirs that affect production: formations, porosity, and permeability, and goes on to discuss wellbore installations and gas lift equipment.



Duration: 3 Hours

The injection of gas into the well fluids in the tubing of an oil well is one method of artificial lift. Gas Lift is a series of three learning programs describing this method in detail. In Operating Techniques, you will learn about gas lift operations, including, operating efficiency, unloading and controlling both continuous and intermittent flow wells, and reading two-pen recorder charts.


Duration: 2 Hours

In this program, you will learn about the components that make up an electronic flow measurement system. You will learn how the major components operate and how to maintain them, and you will learn to read and interpret generic EFM computer printout sheets. The program also provides a comparison of the advantages and disadvantages of EFM to traditional chart-recording meters.



Duration: 6 Hours

In Equipment and Calculations, you will learn about differential pressure within a flowing fluid. The introductory section also defines and discusses rate, velocity and critical flow of a fluid. You will learn about the basic operation of, and the method of measuring with a U-tube manometer, hand-held pitot tubes, permanently installed pitot tubes, calibrated choke nipples, calibrated choke nipples for open-flow potential testing, orifice well testers, and critical flow provers. Also included is a thorough explanation of the operation principles of turbine meters and rotary displacement meters. Finally, you will learn about proving with test meters, with low-pressure flow provers, and with critical flow provers.



Duration: 3 Hours

In Fundamentals of Gas Measurement, you will learn about the physical theory behind gas measurement hardware and practices. This program teaches the relationships between gas pressure, temperature and volume. You will also learn about Boyle's Law, Charles' Law, and the General Gas Law. You will learn about the difference between real and ideal gases, which will also provide the basis for an understanding of super-compressibility, known as the Z factor. The program also explains absolute, gauge and atmospheric pressures, the difference between a temperature scale and its absolute equivalent. Finally, you will learn about the concepts of specific gravity and density. The problem of calculating standard volume from measured volume provides a practical focus for the theory and concepts.



Duration: 4 Hours

Orifice Flow Calculations is an in-depth program covering the measurement of gases flowing through orifice meters. You will learn about the orifice flow rate equation and the eleven factors in the orifice meter flow constant. Tables are provided for the factors so you can work through the field measurement problems.



Duration: 4 Hours

Orifice Meters introduces the learner to the behavior of gases flowing through an orifice meter and to the measurement of that flow. Additionally, this program covers the American Gas Association’s (AGA's) installation recommendations for orifice meters, including both mercury manometer-type and bellows-type meters. Special attention is given to the operation, inspection, and maintenance of pressure and temperature recorders as well as recorder-chart handling and reading. An auxiliary equipment section teaches proper handling of the dead weight tester, the specific gravity balance, the impulse-torque gravitometer and the rotometer. The program concludes with gas measurement economics, including the cost of vented gas loss.



Duration: 2 Hours

In this program, you will learn about the major responsibilities of the witness during an orifice meter test. This program covers the equipment and supplies needed to witness an orifice meter test; identifies what components should be checked during a witnessing session; describes the proper methods for calibrating temperature, static, and differential pressure elements; and describes the required checks for the orifice plate and fitting.

Duration: 5 Hours

In Glycol Dehydration, you will learn about water vapor, the process of glycol dehydration, measuring water content, monitoring equipment, and testing and operations.


Duration: 3 Hours

Heater Treaters: Fundamentals introduces you to the treatment given to crude oil as it is produced. The program covers how emulsions are formed and how stable emulsions are broken by chemical treatment. The program also introduces you to the basics of heater treater construction and operation.



Duration: 3 Hours

Heater Treaters: Types and Operation discusses the construction and operation of horizontal heater treaters, thermal-electric horizontal heater treaters, vertical heater treaters. The program also covers trouble-shooting and heater treater operating economy.

  • Drilling Operations and Systems
  • Exploration Rights and Surface/Subsurface Technologies
  • Fundamentals of Refining
  • Gas Processing Overview
  • Hydrocarbon Recovery
  • Introduction to Solvents
  • Introduction to the Petrochemical Industry
  • Modern Oil and Gas Industry
  • Overview of the Midstream Industry Segment
  • Petroleum Geology
  • Petroleum Reservoirs
  • Pipelines and Storage Systems
  • Production Technology: Flowing Wells and Artificial Lift
  • Reservoir Fluids
  • Steam Cracking
  • Surface Processing of Produced Fluids
  • The E&P Asset Life Cycle
  • Well Completion and Stimulation

  • AC Motors for Operators
  • Air Compressors
  • Centrifugal Compressors: Introduction
  • Centrifugal Compressors: Construction and Operation
  • Centrifugal Pumps: Equipment and Operation
  • Centrifugal Pumps: Introduction
  • Combustion Gas Turbines: Equipment and Operation
  • Combustion Gas Turbines: Introduction
  • Condensers
  • Couplings, Gear Trains, and V-Belts: Gear Trains and V-Belt Drives
  • Couplings, Gear Trains, and V-Belts: Machine Connections and Couplings
  • Electrical Fundamentals
  • Electrical System Basics and Diagrams
  • Heat Exchangers: Introduction
  • Heat Exchangers: Operations and Maintenance
  • Hydrocarbon Chemistry 101
  • Instrumentation: Analyzers and Inferentials
  • Instrumentation: Measuring Liquid Level
  • Instrumentation: Measuring Pressure
  • Instrumentation: Measuring Temperature
  • Instrumentation: Process and Instrumentation Drawings
  • Instrumentation: Regulatory Control
  • Instrumentation: Fundamentals of Control
  • Instrumentation: Measuring Flow
  • Internal Combustion Engines: Introduction
  • Internal Combustion Engines: Operating Techniques
  • Introduction To Compression
  • Introduction to Dynamic Pumps
  • Job Hazard Analysis and Stop Work Authority
  • Leak Detection and Repair
  • Lubrication Concepts
  • Mechanics of Fluids: Fluids in Motion
  • Mechanics of Fluids: Introduction to Process Fluids
  • Mechanics of Fluids: Static Pressure and Head
  • Mechanics of Fluids: Units of Fluid Measurement
  • Mechanics of Fluids: Behavior of Gases
  • Nature of Heat: Fuels and Combustion
  • Nature of Heat: Heat and Temperature
  • Nature of Heat: Heat Exchange Equipment
  • Nature of Heat: Heat Transfer
  • Plant Radio Communication
  • Positive Displacement Compressors: Construction and Operation
  • Positive Displacement Compressors: Introduction

  • Catalytic Reforming
  • Cleaning Activities
  • Cooling Towers: Introduction
  • Cooling Towers: Water Conditioning
  • Corrosion Control
  • Cost Reduction for Operators
  • Fire Fighting: Extinguishing Agents
  • Fire Fighting: Fuels and Combustion
  • Fire Fighting: Portable Fire Extinguishers and Foams
  • Fire Fighting: Strategies
  • Fire Fighting: Tactics
  • Fired Heaters: Equipment and Design
  • Fired Heaters: Operating Techniques
  • Flange Piping
  • Fluid Catalytic Cracking
  • Furnace Operations: Working With Furnaces
  • Introduction to Furnace Operations
  • Performing Skills Assessment
  • Pipe Fitting Basics
  • Practical Distillation: Abnormal Operations
  • Practical Distillation: Behavior of Hydrocarbons
  • Practical Distillation: Fractionating Equipment
  • Practical Distillation: Normal Operations
  • Practical Distillation: Operating Procedures
  • Practical Distillation: Principles and Practices
  • Practical Distillation: Concepts and Quality
  • Process Control Tests
  • Process Operator Responsiblities
  • Process Plant Chemistry
  • Safe Laboratory Operations
  • Safe Tank Cleaning: Cleaning the Tank
  • Safe Tank Cleaning: Gas-Freeing
  • Safe Tank Cleaning: Hazardous Materials
  • Safe Tank Cleaning: Preparing for Cleaning
  • Small Threaded Pipe
  • Statistical Process Control
  • Tubing
  • Valve Maintenance
  • Wastewater Treatment: Biological Treatment Process
  • Wastewater Treatment: Preliminary Treatment
  • Wastewater Treatment: Process Control
  • Wastewater Treatment: Testing and Troubleshooting

  • Basic Core Analysis
  • Coring and Core Preservation
  • Drilling Fundamentals: Part 1
  • Drilling Fundamentals: Part 2
  • Introduction to Artificial Lift
  • Introduction to Hydraulic Fracturing
  • Offshore Systems
  • Plate Tectonics
  • Porosity
  • Special Core Analysis
  • Subsea Systems
  • Well Completion and Stimulation Fundamentals
  • Well Stimulation Methods
  • Wellhead Components

  • Actuators
  • Ambient and Process Chillers
  • Analyzer Sampling and Conditioning System
  • Analyzer Shelters
  • Arc Flash Causes and Mitigation
  • Basic Electronics
  • Batteries
  • Bearings
  • Blinding and De-blinding
  • Cable Duct Banks and Trays
  • Capacitor Banks
  • Cathodic Protection Systems
  • Chlorine Analyzers
  • Circuit Breakers
  • Columns and Process Vessels
  • Compressed Air Dryers
  • Condition Monitoring - Agitators and Mixers
  • Condition Monitoring - Balancing
  • Condition Monitoring - Compressors
  • Condition Monitoring - Electrical Motors
  • Condition Monitoring - General
  • Condition Monitoring - Pumps
  • Condition Monitoring - Turbines, Fans and Blowers
  • Conductivity Analyzers
  • Control Loops
  • Control Systems - SCADA, DCS and ESD
  • Cooling Towers for Technicians
  • Corrosion in Metal
  • Custody Meters
  • Diesel Engine Generators
  • Differential Pressure Flow Measurement
  • Dissolved Oxygen Analyzers
  • Drive Couplings
  • Dust and Coalescer Filters
  • Dynamic Compressor Systems, Seals and Routine Tasks
  • Dynamic Compressors: Introduction and Operation
  • Dynamic Pumps
  • EI&A Field Awareness
  • Electrical Cables
  • Electrical Documentation
  • Electrical Heat Tracing
  • Electrical Level Measurement
  • Electrical Motor Properties, Troubleshooting and Maintenance
  • Electrician's Tools and Test Equipment
  • Emergency Backup
  • Emergency Power Systems
  • Engineering Drawings and Symbols
  • Extruder Equipment
  • Extruder Equipment Maintenance
  • Fans and Blowers
  • Fans and Blowers Maintenance
  • Fasteners
  • Fault Diagnosis, Troubleshooting and Machine Inspections
  • Fiber Optic Cable
  • Filters and Strainers
  • Fire Detection
  • Fire Protection Systems
  • Flame Scanning Devices
  • Flow Gauging (Rotameter)
  • Forklifts
  • Fundamentals of Condition and Predictive Monitoring
  • Fundamentals of Demineralized Water Treatment Systems
  • Fundamentals of Reverse Osmosis Systems
  • Fundamentals of Vibration Measurement
  • Fundamentals Principles of Instrument Calibration 
  • Gala Pellet Dryer for Technicians
  • Gas Chromatography
  • Gas Density Analyzers
  • Gas Detection
  • Gas Insulated Substations (GIS) and Sulfur Hexafluoride (SF6)
  • Gas Turbines for Technicians
  • Gaskets and Packing
  • Gears
  • Grounding
  • Hand and Power Tools for Technicians
  • Hazardous Area and Protection Classifications
  • Heat Exchangers for Technicians
  • High Voltage Gas Insulated Switchgear (GIS)
  • High Voltage Substation Switchgear
  • HVAC Fundamentals
  • Hydraulic Systems
  • Hydrostatic Head Level Measurement
  • Hydrostatic Head Level Measurement - Device Troubleshooting and Calibration
  • Hyper Compressor
  • Industrial Elevators
  • Insulation and Thermal Protection
  • Introduction to AC/DC Electrical Motors for Technicians
  • Introduction to Auxiliary Boiler Systems
  • Introduction to Supervisory Control and Date Acquisition (SCADA)
  • Laydown Yards and Area Management
  • Leak Detection in Refrigeration Lines
  • Lightning Arrester
  • Liquid Nitrogen Storage Systems
  • Low Voltage Substation Switchgear
  • Lubrication Systems, Classifications and Applications
  • LV Intelligent Switchgear
  • Machine Alignment
  • Maintaining HVAC Systems
  • Maintaining Storage Tanks
  • Maintenance Fundamentals
  • Manuals and Drawings
  • Mass Flow Measurement
  • Measurement and Calibration Basics
  • Measuring Tools
  • Mechanical Hoses
  • Medium Voltage Substation Switchgear
  • Medium Voltage Vacuum Contactors
  • Melting Flow Rate Analyzers
  • Microwave and Laser Level Measurement
  • Mixers and Blenders
  • Moisture Analyzers
  • Motor Signature Analysis (MCE)
  • Network and Communication Systems
  • Nuclear Radiation Level Measurement
  • Oxygen Analyzer
  • Pelletizers
  • pH Analyzers
  • Photometric Analyzers
  • Pipe Supports
  • Pipes and Fittings
  • Planned, Corrective, and Breakdown Maintenance
  • Plant Lighting
  • Pneumatic Control Systems
  • Pneumatic Systems
  • Pneumatic Tubing and Fittings
  • Point Level Switches
  • Positive Displacement Pumps for Technicians
  • Potable Water Treatment System
  • Power and Distribution Transformers
  • Power Cables
  • Pressure Measurement
  • Pressure Relief Safety Devices
  • Preventative Maintenance Plans
  • Protective Relays
  • Purging Storage Tanks
  • Radio and Communication Systems
  • Reactors
  • Reciprocating Compressors
  • Regenerative Thermal Oxidizer
  • Reports and Communication
  • Rotary Feeder
  • Rotary Stem Valves for Technicians
  • Rotating Equipment Condition Diagnosis
  • Safety in Instrumentation and Control Systems
  • SCADA Operation
  • Sealing Devices (Gaskets)
  • Security Systems
  • Shell and Tube Heat Exchangers
  • Sight and Float Gauging
  • Simple Control System (PLC)
  • Sliding Stem Valves for Technicians
  • Spark Plugs
  • Special Valves
  • Steam Boilers
  • Steam Condensate Hazards and Removal
  • Steam Traps
  • Steam Turbine Controls
  • Steam Turbines for Technicians
  • Storage Tanks
  • Structural Safety
  • Tank Gauging System
  • Tank Roof Inspection
  • Temperature Measurement
  • Transformer Maintenance
  • Ultrasonic Level Measurement
  • Understanding pH Measurement
  • Uninterruptible Power Supply
  • Utility and Instrument Air Systems
  • Valve Accessories
  • Valve Design and Characteristics
  • Valves Inspection, Testing and Repair
  • Variable Speed and Frequency Drives (VFD/VSD)
  • Vent System and Rundown System
  • Volumetric Flow Measurement
  • Water Softening Systems
  • Weigh Bridges, Docks Levelers & Scales
  • Weighing Devices
  • Workshop Tools and Equipment

  • Amine Sweetening Process
  • Fractionation in Gas Processing
  • Gas Processing Hazards
  • Gas Processing Thermodynamics
  • Hydrocarbon Phase Behavior and Vapor-Liquid Equilibrium
  • Introduction to Gas Processing for Operations
  • Molecular Sieve Dehydration
  • Solid Bed Adsorption and TEG Dehydration
  • Turboexpander Gas Processing Plant

  • Atmospheric and Pressure Storage Tanks
  • Automated Control Applications
  • Chemical Injection Systems
  • Coalescing Filters
  • Condensate Stabilization System
  • Dewpoint Testing/Requirements
  • Electrical Load Centers and Panelboards 
  • Electrical System Basics and Diagrams
  • Electrical System Protection
  • Flare System Fundamentals
  • Flare System Hazards and Ignition
  • Flare System Purging Startup and Shutdown
  • Flowing Pipeline Hydraulics
  • Fractional Distillation Process Fundamentals
  • Fundamentals of Hazardous Area Classifications 
  • Gas Compressor Performance
  • Glycol Dehydration Equipment and Operation
  • Glycol Injection System Operation
  • Glycol Sampling and Testing
  • Heat Medium and Hot Oil Systems
  • Heat Medium System Operation
  • High Pressure Gas Sampling
  • High Pressure Liquid Sampling
  • Hydrates
  • Introduction to Computerized Control Systems
  • Introduction to Gas Chromatography
  • Introduction to Measurement: Density, Moisture, pH, and Conductivity
  • Introduction to Measurement: Level and Flow
  • Introduction to Measurement: Temperature and Pressure
  • Introduction to Pigging
  • Introduction to Pipeline Hydrocarbons
  • Introduction to Pipeline Systems
  • ISO Truck Tank Construction and Inspection
  • Liquid Storage Systems
  • Manifold Systems Overview
  • Measurement Basics and Standards
  • Mercaptan Odorizing Systems
  • Methanol Injection
  • Motor Control Centers (MCCs) 
  • Natural Gas Liquids (NGL) Truck Offloading
  • Non-Destructive Examination (NDE)
  • Operating Hydrogen Sulfide (H2S) Tube Samplers
  • Pentane (C5)+ Truck Loading
  • Pig Launching and Receiving
  • Pipeline Batching
  • Pipeline Bridge Systems
  • Pipeline Commissioning
  • Pipeline Crossings
  • Pipeline Flow Characteristics and Static Pipeline Hydraulics
  • Pipeline Hydrocarbon Measurement and Testing
  • Pipeline In-Line Inspection Tools
  • Pipeline Input/Feed and Export Systems
  • Pipeline Isolation
  • Pipeline Purging with Nitrogen
  • Process Control Strategies
  • Produced Water Treatment
  • Propane and Butane Truck Loading
  • Propane Refrigeration Units and Low Temperature Separators (LTS)
  • Pumping Out Flare Knockout Drums
  • Rail Car Inspection
  • Rail Car Loading and Offloading
  • Rail Car Sampling and Composition Testing
  • Recycle Compressor Operation
  • Reflux in Fractionation Operations
  • Remote Pipeline Startup and Shutdown
  • Roto-Launch Automatic Multiple Pig Launcher
  • Sales Gas Compressor Operation
  • Sales Gas Compressor Types, Use and Limitations
  • Sales Gas Filter Replacement
  • Salt Caverns and Underground Storage
  • Screw Compressor Components and Auxiliary Equipment
  • Solid Desiccants
  • Tank Isolation
  • Tank Venting Systems
  • Testing Composition of Offloading Truck NGLs
  • Tower Fouling and Corrosion Cleaning
  • Turbidity Measurement
  • Two Phase and Three Phase Separators
  • Underground Storage Tank Inspection and Monitoring
  • Water Removal from a Storage Tank Bottom

Process Safety in Operations:

  • Audits and Key Performance Indicators
  • Emergency Response and Incident Investigation 
  • Hazards
  • Introduction
  • Management of Change
  • Projects, Construction and Operations
  • Risk Management

  • Gasoline Blending Operations
  • Refinery Process Overview:
    • Catalytic Reforming
    • Fluid Catalytic Cracking
    • Gasoline Blending
    • Introduction
    • Refinery Process Hazards
    • Crude Distillation
  • Solvent Deasphalting
    • Introduction
    • Analytical Methods and Sample Frequency
    • Primary Equipment
    • Process Operations
    • Process Variables
    • Unit Hazards
  • Sulfur Recovery and Tail Gas Processing Overview
  • Sulfuric Acid Plant:
    • Auxiliary Equipment
    • Introduction and Process Overview
    • Primary Equipment
    • Process Safety
  • SYDEC Delayed Coking Process:
    • Overview
    • Auxiliary Equipment
    • Consequences of Deviation
    • Operations
    • Primary Equipment
    • Process Hazards
  • Turnaround Operations

  • Access to Medical Records
  • Accident Control Techniques: Introduction
  • Accident Control Techniques: Safe Work Practices
  • American Chemistry Council: Responsible Care
  • Asbestos
  • Assessing Occupational Exposure
  • Benzene
  • Combustible Dust Hazards
  • Confined Space Entry
  • DOT Drug and Alcohol Testing
  • DOT Hazardous Materials Employee Safety
  • DOT Hazardous Materials General Awareness
  • DOT Hazardous Materials Transportation Security Awareness
  • Driving Safety
  • EHS Regulatory Overview
  • Electrical Safety for Qualified Employees
  • Electrical Safety for Unqualified Employees
  • Emergency Action Plans, Alarm Systems, and Fire Prevention Plans
  • Environmental Awareness
  • Excavation and Trenching
  • Excavation and Trenching for Operations Personnel
  • Explosive and Flammable Chemicals
  • Export Compliance and Global Trade Guidelines
  • Eye and Face Protection
  • Eye Wash and Safety Showers
  • Fall Prevention
  • First Aid Procedures
  • Forklifts and Powered Industrial Trucks
  • Hand and Power Tool Safety
  • Hand Safety
  • Hazard Communication
  • Hazards of Naturally Occurring Radioactive Materials (NORM)
  • Hazwoper: Awareness
  • Hazwoper: Operations
  • Hazwoper: Overview
  • Hearing Protection
  • Heat Stress Safety
  • Helicopter Safety
  • Hot Work
  • Hydrogen Sulfide (H2S)
  • Incident Reporting and Investigation
  • Industrial Ergonomics
  • Industrial Hygiene
  • Introduction to Hazmat Transportation Regulations
  • Introduction to Process Safety Management (PSM)
  • Ionizing Radiation
  • Irritants, Corrosives, and Sensitizers
  • Jet Fuel Quality Control
  • Laboratory Safety
  • Ladder Safety
  • Ladder Safety for Construction
  • Line Breaking
  • Lockout/Tagout
  • Manual Handling and Lifting Techniques
  • Naturally Occurring Radioactive Materials (NORM)
  • Nitrogen Safe Use and Handling
  • Occupational Exposure to 1,3-Butadiene
  • Occupational Exposure to Bloodborne Pathogens
  • Occupational Exposure to Carcinogens
  • Occupational Exposure to Chlorine
  • Occupational Exposure to Formaldehyde
  • Occupational Exposure to Hexavalent Chromium
  • Occupational Exposure to Hydrochloric Acid
  • Occupational Exposure to Lead
  • Occupational Exposure to Respirable Crystalline Silica
  • Occupational Exposure to Respirable Crystalline Silica - General Industry
  • Occupational Exposure to Sodium Hydroxide (Caustic Soda)
  • Occupational Exposure to Sulfur Dioxide
  • Occupational Exposure to Sulfuric Acid
  • Office Ergonomics
  • Office Fire Safety
  • Office Safety
  • Offshore Water Safety
  • Oxygen-Fuel Gas Welding and Cutting
  • Personal Protective Equipment
  • Portable Fire Extinguishers
  • Portable Fire Extinguishers: Non-Emergency Responder
  • Process Safety and Fatigue Management
  • Process Safety and Fatigue Management for Supervisors
  • RCRA Emergency Response
  • RCRA Generators
  • RCRA Transporters
  • RCRA Treatment, Storage, and Disposal Facilities
  • Respiratory Protection
  • Rigging, Slings and Crane Lifts
  • Scaffolding
  • Security Training:  All Personnel
  • Security Training: Facility Security Officer Overview
  • Security Training: Security Personnel
  • Specifications for Accident Prevention Signs and Tags
  • Spill Prevention, Control, and Countermeasures
  • Storage and Handling of Anhydrous Ammonia
  • Toxic Chemicals
  • Toxic Substances Control Act (TSCA)
  • Unstable and Reactive Chemicals
  • Vehicle-Mounted Elevated Work Platforms and Aerial Lifts
  • Walking/Working Surfaces
  • Warehouse Safety
  • Working on Scaffolds
  • Workplace Violence

  • Access to Medical Records - UK
  • Asbestos - UK
  • Assessing Occupational Exposure - UK
  • Benzene - UK
  • Confined Space Entry - UK
  • Driving Safety - UK
  • Electrical Safety for Qualified Employees - UK
  • Electrical Safety for Unqualified Employees - UK
  • Environmental Awareness - UK
  • Excavation and Trenching - UK
  • Explosive and Flammable Chemicals - UK
  • Eye and Face Protection - UK
  • Eye Wash and Safety Showers - UK
  • Fall Prevention - UK
  • First Aid Procedures - UK
  • Forklifts and Powered Industrial Trucks - UK
  • Hand Safety - UK
  • Hazardous Waste Spill Response, Containment and Decontamination - UK
  • Hearing Protection - UK
  • Heat Stress Safety - UK
  • Helicopter Safety - UK
  • Hot Work - UK
  • Hydrogen Sulphide (H2S) - UK
  • Incident Reporting and Investigation - UK
  • Industrial Ergonomics - UK
  • Industrial Hygiene - UK
  • Ionising Radiation - UK
  • Irritants, Corrosives, and Sensitizers - UK
  • Laboratory Safety - UK
  • Ladder Safety - UK
  • Line Breaking - UK
  • Lockout/Tagout - UK
  • Manual Handling and Lifting Techniques - UK
  • Naturally Occurring Radioactive Materials (NORM) - UK
  • Nitrogen Safe Use and Handling - UK
  • Occupational Exposure to 1,3-Butadiene - UK
  • Occupational Exposure to Bloodborne Pathogens - UK
  • Occupational Exposure to Carcinogens - UK
  • Occupational Exposure to Chlorine - UK
  • Occupational Exposure to Formaldehyde - UK
  • Occupational Exposure to Hexavalent Chromium - UK
  • Occupational Exposure to Hydrochloric Acid - UK
  • Occupational Exposure to Lead - UK
  • Occupational Exposure to Sodium Hydroxide (Caustic Soda) - UK
  • Occupational Exposure to Sulphur Dioxide - UK
  • Occupational Exposure to Sulphuric Acid - UK
  • Office Ergonomics - UK
  • Office Fire Safety - UK
  • Office Safety - UK
  • Offshore Water Safety - UK
  • Overview of Hazardous Waste Operations and Emergency Response - UK
  • Oxygen-Fuel Gas Welding and Cutting - UK
  • Personal Protective Equipment - UK
  • Portable Fire Extinguishers - UK
  • Portable Fire Extinguishers: Non-Emergency Responder - UK
  • Process Safety and Fatigue Management - UK
  • Process Safety and Fatigue Management for Supervisors - UK
  • Respiratory Protection - UK
  • Rigging, Slings and Crane Lifts - UK
  • Specifications for Accident Prevention Signs and Tags - UK
  • Spill Prevention, Control, and Countermeasures - UK
  • Storage and Handling of Anhydrous Ammonia - UK
  • Toxic Chemicals - UK
  • Unstable and Reactive Chemicals - UK
  • Vehicle-Mounted Elevated Work Platforms and Aerial Lifts - UK
  • Walking/Working Surfaces - UK
  • Warehouse Safety - UK
  • Workplace Violence - UK

Download e-Learning Information